Численное моделирование трехмерного течения и теплообмена в условиях, типичных для организации пленочного охлаждения
Диссертация
В настоящее время численное моделирование пространственного турбулентного течения и теплообмена при пленочном охлаждении базируется преимущественно на решении осредненных по Рейнольдсу уравнений Навье-Стокса в совокупности с одной из моделей турбулентности (в англоязычной научной литературе этот метод обозначается аббревиатурой RANS, Reynolds-Averaged Navier-Stokes). Метод RANS относительно… Читать ещё >
Список литературы
- Абрамов А.Г., 2003. Метод моделирования крупных вихрей в приложении к задачам турбулентной конвекции в подогреваемых снизу емкостях: варианты и возможности / Дисс. канд. физ.-мат. наук — СПб: СПбГТУ, 2003.
- Абрамович Г. Н., 1960. Теория турбулентных струй, Физматгиз.
- Богомолов Е.Н., 1987. Рабочие процессы в охлаждаемых турбинах газотурбинных двигателей с перфорированными лопатками. М.: Машиностроение, 1987, 160с.
- Веретенников С.В., 2005. Исследование характеристик завесы при охлаждении пластины с различными вариантами организации подвода охладителя // Тр. XV Школы-семинара под рук. акад. РАН А. И. Леонтьева. М.: Изд-во МЭИ, 2005, Т.2, С.25−28.
- Владимирова И.И., Кузнецов Б. Г., Яненко Н. Н., 1966. Численный расчет симметричного обтекания пластинки плоским потоком вязкой несжимаемой жидкости / В сб.: Некоторые вопросы вычислительной и прикладной математики. Новосибирск. 1966. С. 186−192.
- Гарбарук А.В., 1999. Современные полуэмпирические модели турбулентности для пристенных течений: тестирование и сравнительный анализ / Дисс. канд. физ.-мат. наук СПб: СПбГТУ, 1999.
- Копелев С.З., 1983. Охлаждаемые лопатки газовых турбин (тепловой расчет и профилирование). М.: Наука, 1983, 144с.
- Лойцянский Л.Г., 1973. Механика жидкости и газа. М.: Наука, 1973 — 848с.
- Монин А.С., 1988. Теоретические основы геофизической гидродинамики. Л.: Гидрометеоиздат, 1988. 424 с.
- Нино М.Н., Уайтло Дж., 1971. Эффективность пленочного охлаждения при комбинации тангенщгальных и нормальных к стенке отверстий. Энергетические машины и установки, № 4, 1971, стр. 68, изд-во Мир.
- Рамсей Дж., Гольдштейн Р., 1971. Взаимодействие вдуваемой нагретой струи с основным потоком. Теплопередача, № 4, 1971, стр. 41, изд-во Мир.
- Себиси Т., Брэдшоу П., 1987. Конвективный теплообмен. Физические основы и вычислительные методы: Пер. с англ. М.: Мир, 1987. (Cebeci Т., Bradshaw Р. Physical and Computational Aspects of Convective Heat Transfer. Springer-Verlag, 1984).
- Смирнов П. Е., 2005а. Относительно простой способ учета анизотропии турбулентности при трехмерном численном моделировании ближнего поля струи, выдуваемой для организации пленочного охлаждения // Труды XV Школы
- Ф семинара молодых ученых и специалистов под руководством акад. РАН А.И.
- Смирнов Е.М., Зайцев Д. К., 2004. Метод конечных объемов в приложении к задачам гидрогазодинамики и теплообмена в областях сложной геометрии // Научно-технические ведомости СПбГПУ, 2004, № 3, С. 70−81.
- Флетчер К., 1991. Вычислительные методы в динамике жидкостей: В 2-х т.: Т.2.: Пер. с англ.-М.: Мир, 1991.-552 с.
- Afejuku W.O., Hay N., Lampard, D., 1980. Film cooling effectiveness of double rows of holes // ASME J. Engineering for Power 1980. — Vol.102 — P.601−606.
- Ajersch, P., Zhou, J.-M., Ketler, S., Salcudean, M., Gartshore, I. S., 1995. Multiple jets in a cross flow: detailed measurements and numerical simulations // ASME Pap. 95-GT-9.
- Azzi A., Lakehal D., 2002. Perspectives in modelling film-cooling of turbine blades by transcending conventional two-equation turbulence models // ASME J. Turbo-machinery. 2002. — Vol. 124(3). — P. 472−484.
- Baldwin, B.S., Lomax, H., 1978. Thin-layer approximation and algebraic model for separated turbulent flows // AIAA Paper 1978. — Vol. 78 — P. 257.
- Barringer, M. D., Richard, О. Т., Walter, J. P., Stitzel, S. A/., Thole, K. A., 2002. Flow field simulations of a gas turbine eombustor // J. of Turbomachinery. 2002. -Vol.124.-P. 508−516.
- Bergeles, G., Gosman, A. D., Launder, В. E., 1978. The turbulent jet in a cross stream at low injection rates: a three-dimensional numerical treatment // Numer. Heat Transfer. 1978. — Vol.1. — P. 217−242.
- Bohn D., Kusterer K., 1998. 3D numerical aerodynamic and combined heat transfer analysis of a turbine guide vane with showerhead ejection // In: Proc. of 11th IHTC Heat Transfer, 1998, Vol. 4, Kyongju, Korea.
- Boris, J.P., MacArthur, C.D., Rivir, R.B., 1994. The effect of high freestream turbulence on film cooling effectiveness // ASME Pap. 94-GT-51.
- Boussinesq, J., 1877. Theorie de Tecoulement tourbillant / Mem. Presentes par Divers Savants Acad. Sci. Inst. Fr. -1877. Vol. 23. — P. 46−50.
- Burd, S. W., Kaszeta, R. W., Simon, T. W, 1996. Measurements in film cooling flows: hole L/D and turbulence intensity effects. // ASME Pap. 96-WA/HT-7.
- Burd, S., Simon, T. W, 1997. Influence of coolant supply geometry on film coolant exit flow and surface adiabatic effectiveness // ASME Pap. 97-GT-25.
- Chen K.H., 1995. A diagonally-dominant coupled strongly implicit procedure for 3D viscous flows / In: Proc. First Asian CFD Conference, Hong Kong, January 1619, 1995. P.325−333.
- Chen, H.-C., Wei, G., Han, J.-C., 1999. Computation of discrete-hole film cooling by a near-wall second-moment turbulence closure // ASME-IMECE, Nashville, TN.
- Chorin, A.J., 1967. A numerical method for solving incompressible viscous flow problems // J. Comput. Phys. 1967. — Vol. 2. — P. 12−26.
- Claus, R.W., Vanka, S. P., 1990. Multigrid Calculations of Jet in Crossflow//AIAA Pap. 90−0444.
- Cokljat D., Kim S. E., laccarino G., Durbin P. A., 2003. A comparative assessment of the v2-f model for recirculating flows // AIAA Pap. 2003−0765.
- Demuren A.O., 1983. Numerical calculations of steady three-dimensional turbulent jets in cross flow // Сотр. Meth. App. Mech. Engr. 1983. — Vol. 37. — P. 309−328.
- Demuren, A.O., 1986. Modeling turbulent jets in crossflow, Encyclopedia of Fluid Mechanics, Editor Gulf Publishing, 1986, Vol. 2.• 45. Durbin P. A., 1995. Separated flow computations with the k-e-v2 model // AIAA J.- 1995. Vol. 33. — P.659−664.
- Ericksen V.L., Goldstein R.J., 1974. Heat transfer and film cooling following injection through inclined circular tubes // J. of Heat Transfer 1974 — Vol.96. — P.239−245.
- Findlay, M., J., He, P., Salcudean, M., Gartshore, I., S., 1996. A row of streamwise-inclined jets in crossflow: measurements and calculations // ASME Pap. 96-GT-167.
- Ferguson, D. J., Walters, K. D., Leylek, J. H., 1998. Performance of turbulence models and near-wall treatments in discrete jet film cooling simulations // ASME Pap. 98-GT-438.
- Ferziger, J. H., Peric, M, 1999. Computational methods for fluid dynamics, (2nd ed.), Springer-Verlag, Berlin. 1999.
- Garg, V. K., 1999. Heat transfer on a film-cooled rotating blade using different tur• bulence models // Int. J. of Heat and Mass Transfer. 1999. — Vol.42. — P.789−802.
- Garg, V. K., 2000. Heat transfer on a film-cooled rotating blade // Int. J. Heat and Fluid Flow 2000. — Vol. 21. — P. 134−145.
- Garg, V. K., Ameri, A. A., 1997. Comparison of two-equation turbulence models for prediction of heat transfer on film-cooled turbine blades // Numerical Heat Transfer.- 1997. Vol. 31.-P.347−371.
- Garg, V. K., Gaugler, R. E., 1997. Effect of velocity and temperature distribution at the hole exit on film cooling of turbine blades // ASME Journal of Turbomachinery.- 1997.-Vol. 119(2).-P. 343−351.
- Germano, M., 1990. Turbulence: the filtering approach. // J. Fluid Mech. 1990. -Vol. 238. — P. 325.
- Gibson, M. M, Launder, В. E., 1978. Ground effects on pressure fluctuations in the atmospheric boundary layer //J. Fluid Mech. 1978. — Vol.86. — P.491−511.
- Goldstein, R.J., Eckert, E.R., Ramsey, J.W., 1968. Film cooling with injection through holes: adiabatic wall temperatures downstream of a circular hole // ASME J. Engineering for Power. 1968. — Vol. 90. — P. 384−395.
- New York and London, 1971 Vol.7. — P.321.
- Goldstein, R. J., Eckert, E. R. G., Burggraf, F., 1974. Effects of hole geometry and density on three-dimensional film cooling // Int. J. Heat Mass Transfer. 1974. -Vol.17.-P. 595−607.
- Hahn S., Choi H., 1997. Unsteady simulation of jets in a cross flow // J. Computational Physics. 1997. — Vol.134 (2). — P.342−356.
- Han, S., Goldstein, R., 2002. Film cooling effectiveness for a single row of discrete injection holes influence of hole orientation, shape and blowing rate // In: Proc. of 12th Int. Heat Transfer Conference, Vol.2, P. 357−362.
- Hanjalic K., Popovac M., Hadziabdic M., 2004. A robust near-wall elliptic-relaxation eddy-viscosity turbulence model for CFD // Int. J. of Heat and Fluid Flow. -2004.-Vol. 25.-P. 1047−1051.
- Hanjalic K, Laurence D. R., Popovac M., Uribe J.C., 2005. V2/k-f turbulencemodel and its application to forced and natural convection // ERCOFTAC ETMM-6 conference, Sardinia, May 2005, Elsevier.
- Hoda, A., Acharya, S., 2000. Predictions of a film cooling jet in cross-flow with different turbulence models // ASME J. Turbomachinery. 2000. — Vol.122. -P.558−569.
- Hoda, A., Acharya, S" Tyagi, M., 2000. Predictions of a Jet-In-Crossflow with Reynolds Stress Transport Models and Large Eddy Simulations. // ASME-Intl. Gas Turbine Conference. 2000, Munich.
- Jabbari M.Y., Goldstein R.J., 1978. Adiabatic wall temperature and heat transfer downstream of injection through two rows of holes // ASME J. Engineering for Power. 1978 -Vol.100-P. 303−307.
- Jones W.P., McGuirk J.J., 1980. Computation of a round turbulent jet discharging into a confined crossflow // Turbulent Shear Flows, Springer-Verlag, Berlin, Vol.2, P.233−245.
- Kaszeta, R. W., Simon, T. W" Оке, R. A., Burd, S. W. 1998. Flow measurements in film cooling flows with lateral injection // ASME Pap. 98-GT-54, presented at the 1998 Int’l. Gas Turbine Conf., Stockholm, Sweden.
- Knost, D. G., Thole, К A., 2003. Computational predictions of endwall film-cooling for a first stage vane // ASME Pap. GT-2003−38 252.
- Kxvak, D., Chang, J.L.S., Shanks, S.P., Chakravarthy, S.R., 1986. A three-dimensional incompressible Navier-Stokes flow solver using primitive variables // AIAA Journal. 1986. — Vol. 24. — P.390−396.
- Lakehal, D., 2002. Near-wall modelling of turbulent convective heat transport in film cooling of turbine blades with the aid of DNS data // ASME J. Turbomachinery.• -2002,-Vol. 124(3).-P. 485−498.
- Lakehal, D" Theodoridis, G., Rodi, W., 1998. Computation of film cooling of a flat plate by lateral injection from a row of holes // Int. J. Heat Fluid Flow. 1998 -Vol.19.-P.418−430.
- Lakehal, D., Theodoridis, G., Rodi, W., 2001. Three dimensional flow and heat transfer calculations of film cooling at the leading edge of a symmetrical turbine blade model // Int. J. Heat Fluid Flow. 2001 — Vol.22 — P. l 13−122.
- Lakshminarayana, В., 1996. Fluid Dynamics and Heat Transfer of Turbomachinery, N.Y., Wiley, 1996, 809p.
- Lam С. K. G., Bremhorst, K. A., 1981. Modified form of the k-e model for predicting wall turbulence//J. of Fluid Engineering. 1981. -Vol. 103. — P. 456−460.
- Launder, В. E., 1989. Second-moment closure: Present. and Future? // Inter. J. Heat Fluid Flow. 1989. — Vol. 10(4). — P. 282−300.
- Launder, B.E., Spalding, D.B., 1974. The numerical computation of turbulent flows // Comput. Methods Appl. Mech. Eng. 1974. — Vol. 3. — P. 269−289.
- Launder, В. E., Reece, G. J., Rodi, W., 1975. Progress in the development of a Reynolds-stress turbulence closure // J. Fluid Mechanics. 1975. — Vol.68(3). -P. 537−566.
- Le H., Moin P., Kim J., 1997. Direct numerical simulation of turbulent flow over abackward-facing step // J. Fluid Mechanics. 1997. — Vol. 330. — P. 349−374.
- Leonard, A., 1974. Energy cascade in large eddy simulations of turbulent fluid flows // Adv. In Geophys. 1974. — Vol. 18A. — P. 237.
- Leonard B.P., 1979. A stable and accurate convective modelling procedure based on quadratic upstream interpolation // Comput. Methods Appl. Mech. Eng. 1979. -Vol. 19. — P.59−98.
- Leylek, J. H., Zerkle, R. D., 1994. Discrete-jet film cooling: a comparison of computational results with experiments // ASME J. Turbomachinery. 1994. — Vol.116. -P.358−368.
- Lien F. S., Durbin P. A., Parneix S" 1997. Non-linear v2-f modeling with application to aerodynamics flows // Proc. 11th Symposium on Turbulent Shear Flows. Paper 6−19. 1997. P. 6.
- Lund, Т., Wu, X., Squires, K., 1998. Generation of turbulent inflow data for spatially-developing boundary layer simulations // J. Computational Physics. — 1998. -Vol.140.-P. 233−258.
- Lutum, E., Johnson, В. V., 1999. Influence of the hole length-to-diameter ratio on film cooling with cylindrical holes // ASME J. Turbomachinery. 1999. — Vol. 121. — P.209−216.
- Mayhew J.E., Baughn J. IV., Byerley A.R., 2002. The effect of freestream turbulence on film cooling effectiveness // ASME Pap. GT-2002-30 172.
- Medic G., Durbin P., 2002. Toward improved prediction of heat transfer on turbine blades // ASME J. Turbomachinery. 2002. — Vol. 124. — P. 187−192.
- Menter F. R., 1994. Two-equation eddy-viscosity turbulence models for engineering applications // AIAA J. 1994. — Vol. 32. — P. 1598−1605.
- Mulduun, F., Acharya, S., 1999. Numerical investigation of the dynamical behavior of a row of square jets in crossflow over a surface // ASME-IGTI 99.
- Ooi A., Iaccarino G., Durbin P. A., Behnia M., 2002. Reynolds averaged simulation of flow and heat transfer in ribbed ducts // J. Heat and Fluid Flow. 2002. — Vol.23. — P.750−757.
- Patankar, D.K. Basu, S.A. Alpay, 1977. Prediction of the three-dimensional velocity field of a deflected turbulent jet // Journal of Fluids Engineering. 1977. — Vol.99. -P.758−62.
- Patankar, S. V., 1980. Numerical Heat Transfer and Fluid Flow, Hemisphere Publishing Corporation, New York.
- Pedersen D.R., Eckert E.R., Goldstein R.J., 1977. Film cooling with large density differences between the mainstream and the secondary fluid measured by the heat-mass transfer analogy // ASME J. of Heat Transfer. 1977. — Vol. 99. — P. 620−627.
- Pietrzyk J.R., Bogard D.G., Crawford M.E., 1989. Hydrodynamic measurements of jets in crossflow for gas turbine film cooling applications // ASME J. Turbomachin-ery- 1989-Vol.111 -P.139−145.
- Pietrzyk J.R., Bogard D.G., Crawford M.E., 1990. Effect of density ratio on the hydrodynamics of film cooling // ASME J. Turbomachinery 1990 — Vol.112 — P. 437 443.
- Radomsky, R. W., Thole, K. A., 2000. Flowfield measurements for a highly turbine flow in a stator vane passage // J. of Turbomachinery. 2000. — Vol.122. -P.255−262.
- Rastogi A. K, Whitelaw J.H., 1973. The effectiveness of three-dimensional film cooling slots I. Measurements. // Int. J. Heat Mass Transfer — 1973. — Vol.16. -P.1665.
- Q4. Rhie C.M., Chow W.L., 1983. A numerical study of the turbulent flow past an isolated airfoil with trailing edge separation // AIAA Journal. 1983. — Vol. 21. -P.1525−1532.
- Rodi, W., 1991. Experience with two-layer models combining the k-e model with a one-equation model near the wall // AIAA Pap. 91−0216.
- Roe, P. L., 1981. Approximate Riemann solvers, parameter vectors and difference schemes // J. Computational Physics. 1981. — Vol. 43. — P.357−372.
- Rogers, S. E., Kwak, D., 1990. Upwind differencing scheme for the time-accurate incompressible Navier-Stokes equations // AIAA J. 1990. — Vol.28. — P. 253−262.
- Roy, S., Kapadia, S., Heidmann, J.D., 2003. Film cooling analysis using des turbulence model // ASME Pap. GT-2003−38 140, presented at Proc. of ASME Turbo Expo, June 16−19, 2003, Atlanta, Georgia.
- Schmidt D.L., Bogard D.G., 1996. Effects of freestream turbulence and surface roughness on film cooling // ASME Pap. 96-GT-462.
- Sinha A.K., Bogard D.G., Crawford M.E., 1991a. Film cooling effectiveness downstream of a single row of holes with variable density ratio // ASME J. Turbomachinery. 1991. — Vol. 113. — P. 442−449.
- Sinha A.K., Bogard D.G., Crawford M.E., 1991b. Gas turbine film cooling: flow field due to a second row of holes // ASME J. Turbomachinery. 1991. — Vol. 113.-P. 450−456.
- Smagorinsky J., 1963. General circulation experiments with the primitive equations. I. The basic experiments // Mon. Weather Rev. 1963. — Vol. 91. — P. 99−164.
- Smirnov, E.M., 2000. Solving the Full Navier-Stokes Equations for Very-Long
- Heat Fluid Flow. 2000. — Vol.21. — P.252−263.121 .Spalart, P.R., Allmaras, S.R., 1994. A one-equation turbulence model for aerodynamic flows // La Rech. Aerospatiale 1994. — Vol. 1. — P.5−21.
- Spalart P.R., Shur M.L., 1997. On the sensitization of simple turbulence models to rotation and curvature // Aerosp. Sc. and Techn. 1997. — Vol. 1(5). — P.297.
- Strelets, M., 2001. Detached eddy simulation of massively separated flows // AIAA Pap. 2001-0879, 2001, 18p.
- Tyagi, M., Acharya, S., 1999a. Large eddy simulations of rectangular jets in cross-flow: effect of hole aspect ratio // Recent Advances in DNS and LES, Second AFSOR Conference on DNS/LES, Eds D. Knight and L. Sakell, P. 431−442.
- Tyagi, M., Acharya, S., 2003. Large eddy simulation of film cooling flow from an inclined cylindrical jet // ASME J. Turbomachinery. 2003. — Vol. 125 — P.734−742.
- Vogel J. C., Eaton J. K., 1985. Combined heat transfer and fluid dynamics measurements downstream of a backward-facing step // ASME J. Heat Transfer. 1985. -Vol. 107.-P. 922−929.
- Walters, K. D., Leylek, J. H., 1996. A systematic computation methodology applied to a three-dimensional film-cooling flowfield / ASME Pap. 96-GT-351.
- Walters, K. D., Leylek, J. H., 1997. A detailed analysis of film-cooling physics, part i: streamwise injection with cylindrical holes / ASME Pap. 97-GT-269.
- Wang, L., Tsang, H., Simon, T. W., Eckert, E. R. G., 1996. Measurements of a mean flow and eddy transport over a film cooling surface // In: Proceedings of the 31st National Heat Transfer Conference, vol. 5, ASME-HTD, 1996, Vol. 327, P. 71−79.
- Wilcox, D.C., 1993. Turbulence modeling for CFD / Griffin Printing, Glendale, California, 1993.
- Wolfshtein, M., 1969. The velocity and temperature distribution in one-dimensional • flow with turbulence augmentation and pressure gradient // Int. J. Heat and Mass
- Transfer. 1969. — Vol. 12. — P. 301−318.
- Yoshizawa, A., Horiuti, K., 1985. A statistically-derived subgrid-scale kinetic energy model for the large-eddy simulation of turbulent flows // J. Phys. Soc. Jpn. -1985. Vol. 54. — P. 2834−2839.
- Yuan L.L., Street, R. L., 1996. Large eddy simulation of a jet in crossflow // ASME Fluids Engineering Division. 1996. — Vol. 242. — P.253−260.
- Zhou, J.M., Saculdean, M., Gartshore, I., 1993. Prediction of film cooling by discrete-hole injection // ASME Pap. 93-GT-75.